-Electronics powered via bus voltage or via USB by a connected PC -Plug onto UP 110 or UP 114 bus coupling unit -Transmission PC – USB 1.1 or higher -Electrically isolated access to the bus line via integrated socket USB (type B) -Access to all bus devices in the system The bus trasnceiver module BCU1/2 must be ordered separately. See Chapter Display and Operation Units - Pushbutton accessories.The matching desin frame must be ordered separately. See chapter Display and Operation Units.

-Electronics powered via bus voltage or via USB by a connected PC -Plug onto UP 110 or UP 114 bus coupling unit -Transmission PC – USB 1.1 or higher -Electrically isolated access to the bus line via integrated socket USB (type B) -Access to all bus devices in the system

-For communication via KNX EIB with electronic ballasts with a DALI interface -DALI output acc. to IEC 60929, for communication with up to 64 DALI ballasts -Integrated power supply with input voltage AC/DC 110...240 V, 50...400 Hz, for powering the gateway electronics and DALI output -Maximum DALI output voltage of 16 V, short circuit resistant -Green LED for displaying the operating voltage -Pushbutton for switching between bus and direct operating mode -Yellow LED for displaying direct mode -One pair of push buttons for switching On/Off of all connected DALI ballasts -One red LED in the switching button for displaying the switching state of all DALI ballasts (permanent LED light) and displaying a DALI fault condition by blinking -Control (switching, dimming, and setting dimming value) as well as feedback of status and lamp failure of up to 64 DALI ballasts -Operation of each DALI ballast either as individual device or as member of one of up to 16 DALI groups -Configurable assignment of the DALI ballasts to up to 16 DALI groups, which can only be switched and dimmed in groups including reporting status and lamp failures in groups -Control (switching, dimming, setting dimming value) of self-contained emergency luminaires as individual luminaires or as member of a DALI group -Distinction between self-contained emergency luminaires with one or two DALI devices -Starting the self-conducted testing of each individual inverter and reporting the test result via bus -Distinction between function test, short duration test, and long duration test -Optional configuration of any DALI ballast to dim to a preset dimming value in case of emergency mode -Locking of switching and dimming commands as well as configuration while emergency mode is activated -Activation of emergency mode based on a configurable number of failed DALI ballasts -Transformation of dimming commands into a temporary set point adjustment for ballasts with integrated constant light level control and directly connected light level sensor -One or two level timer -Integrated scene control for up to 16 scenes -Integrated one time or cyclical control of repeatable sequences or color effects -Possible assignment of a CIN to a DALI ballast and with commissioning of DALI ballasts and test of channel, scene, and effect functionality within ETS -Integrated bus coupling unit -Only half a standard bus load -Bus connection via bus terminal or contact system to data rail -For mounting on DIN rail EN 60715-TH35-7.5 The data rail must be ordered separately. See chapter System Products and Accessories - data rails.

Rated operational voltage 230 V AC, 50 Hz The matching design frame must be ordered separately.The flush-mounting/hollow-wall box must be ordered separately.

Rated operational voltage 24 V AC/DC, power consumption approx. 400 mA The matching design frame must be ordered separately.The flush-mounting/hollow-wall box must be ordered separately.

Нет описания

Нет описания

8 facing pushbutton rockers Аксессуары для клавиш UP223 и UP287 с ИК-приёмником и декодером

Flush-mounting/hollow-wall boxes for UP 588 touch panels

In order to use antitheft screws with bus terminals, such as pushbuttons, room temperature controllers etc., on UP 110/11 bus coupling units, 2 mounting brackets per bus coupling unit are required

-8 configurable inverting of inputs (virtual) -4 configurable inverting of outputs -2 user-definable logic gates -Positively driven on/off switching of loads (4 channels) -Partition control: 4 partition inputs, 4 controllable rooms, switching commands (2 x 1 bit), brightness values (1 byte), switch/dimming commands (1 bit, 4 bit) -Bus-powered electronics -Integrated bus coupling units, Bus connection via contact system to data rail -Modular installation devices for mounting on TH35 EN 60715 mounting rail The data rail must be ordered separately. See chapter System Products and Accessories - data rails.

-8 inputs for DC or AC in the range from 12 to 230 V -8 relay contact outputs locked in pairs against each other for controlling 4 ? AC 230V sunblind drives -Contact rated voltage AC 230 V -Contact rated current 6 A, p.f. = 1 -Electronics powered by a 230 V AC integrated power supply -Device functional even without bus connection or if the bus communication fails -Preset on delivery for direct output control for each blind button function via momentary contact switches connected to the inputs -Green LED to indicate standby -Key for switching between bus and direct mode -Yellow LED for indicating direct mode activated -Button for each relay contact output, for switching the output in direct mode while the button is held down -LED per input to indicate the relevant signal status -Selectable function for each input when using the ETS: -Switching status, send binary value -Switching on leading edge, switching Short/Long -1-pushbutton dimming, sunblind control, group control -1-bit/8-bit scene control -8-bit/16-bit value leading edge, Short/Long -16-bit floating point value leading edge, Short/Long -Or for each pair of inputs: -Acting directly on the corresponding outputs as blind button -2-button dimming with stop telegram or with cyclical sending -2-pushbutton sunblind control -Selectable blocking of each input via a corresponding blocking object -Sending of input objects after change -Selectable cyclical input object sending -Individual or shared configuration of actuator channels -Communication objects for each blind channel for driving the sun protection into the end positions or for stopping the procedure and adjusting the blind slats in steps -Communication objects for setting position of slats and blinds in percentage information -Automatic opening of the blind slats to a preconfigured nominal setting after uninterrupted driving down of the blind from the top to the bottom end position, with integrated 1-bit scene control for storing and calling up (reproduction) of 2 interim blind and slat settings -Integrated 1-bit/8-bit scene control, 8 scenes can be integrated per channel -Optional Sun object for integration in a sunlight tracking control system -Differentiation between automatic and manual mode and with automatic switchover from automatic to manual mode for the channel in question by pressing a bus button for manual control of the corresponding sun protection -Manual mode taking precedence over automatic position commands -Optional central command for each device or each channel for switching the relevant channels to automatic mode and driving the sun protection into the up or down end position -Alarm: move to safety position, Locking in this position for as long as alarm is active -Travel lock (e. g. for cleaning the outer shutter/blinds) -Status objects for each channel for querying or for automatic sending of sun protection and slat settings as a percentage value -Optional status objects for reporting that the up or down position has been reached -Integrated bus coupling unit -Bus connection via bus terminal or contact system to data rail -Modular installation devices for mounting on TH35 EN 60715 mounting rail The optional data rail must be ordered separately. See chapter System Products and Accessories - data rails.

-8 inputs AC/DC 12...230 V -8 relay contact outputs -Rated contact voltage AC 230 V -Rated contact operating current 16 A, p.f. = 1 -Electronics power supply via an integrated power supply unit for AC 230 V -Device functional even without bus connection or if bus voltage absent or bus communication interrupted or not yet activated -Green LED to indicate operational readiness -Push button to switch between bus and direct mode -Yellow LED to indicate direct mode activated -Push button for each output to switch the output in direct mode via a toggling function by a short actuation and for changing the output mode between remote control relay and time switch relay by holding down the push button for some seconds -1 red LED per output to indicate the switching state -1 red LED per input to indicate the current signal state -Device preset at the factory for direct switching of an output through a toggling function via the input of the same name -Selectable function for each input when using the Engineering Tool Software (ETS): -Switching status / binary value transmission -Switching, short / long operation -Single button dimming, single button sun protection control, 1-button group control (sequence control) -1-bit scene control -8-bit scene control, 8-bit value, edge-triggered, 8-bit value, short / long operation -16-bit floating point value, edge-triggered, 16-bit value, short / long operation, 16-bit value, edge-triggered, 16-bit floating point value, short / long operation -Selectable function for each pair of inputs: 2-button dimming with stop telegram, 2-pushbutton shutter/blind control -Selectable blocking / releasing of each input via a corresponding blocking object -Sending of the input objects after a change of status -Selectable logic operation (AND/OR) for one input with a further communication object and with variable start value of the logic operation at bus voltage recovery -Setting by means of the ETS, whether all outputs are to be configured identically or individually -Selectable mode for each output (normal mode, time switch mode) -Optional addition of a night mode object for each output for time-limited switching On of the output (and hence the illumination) at night -Variable On and Off delay times for each output -Variable On period in night mode or in time switch mode -Selectable warning signal prior to imminent switching-off by means of three-times short off and on switching (flashing) in night mode or in time switch mode -Status object for reporting direct mode -Optional status object per output for status reporting -Sending of status objects on request and/or automatically after a change -Integrated 8-bit scene control and linking of each output with up to 8 scenes -Selectable switching state for each output at mains or bus power failure as well as after bus or mains voltage recovery -Integrated bus coupling units with only half a standard bus load -Bus connection via bus terminal or contact system to data rail -Modular installation devices for mounting on TH35 EN 60715 mounting rail The optional data rail must be ordered separately. See chapter System Products and Accessories - data rails.

-1 x AC 230 V, 6 A, 2 x binary inputs -1 channel -For the separate control per actuator channel of a sun protection‚ damper‚ door or window drive with a motor for AC 230 V and electromechanical limit switches -Electrically interlocked relays (for reversing direction of rotation) -Max. cable length, unshielded, twisted 5 m -For 2 signal inputs (floating contact) -Determination of switching state by means of the voltage generated in the device -Configurable behavior in the event of a bus voltage failure -Configurable behavior in the event of a bus voltage recovery -Transmitting status per channel -Travel lock (e. g. for cleaning the outer shutter/blinds) -Alarm (Wind, Rain, Frost): Move to safety position, locking in this position for as long as alarm is active -Individual configuration of actuator channels -Travel to end position, stopping, stepwise adjustment -Bus-powered electronics -Integrated bus coupling units -Bus connection via bus terminal -For installation in flush-mounting switch and socket boxes with ? 60 mm

-2 channels -For the separate control per actuator channel of a sun protection‚ damper‚ door or window drive with a motor for AC 230 V and electromechanical limit switches -Integrated isolating relay function for connection of 2 drives per channel -Electrically interlocked relays (for reversing direction of rotation) -Rated contact voltage AC 230 V, 50 Hz -Rated contact current 6 A -Configurable behavior in the event of a bus voltage failure -Alarm (Wind, Rain, Frost): Move to safety position, locking in this position for as long as alarm is active -Shared configuration of actuator channels -Adaptation of objects and functions to drive type -Sun protection control (up/down) -Using position data (8-bit value) -Travel to end position, stopping, stepwise adjustment -Slat control (open/closed) -Using position data (8-bit value) -Travel to end position, stopping, stepwise adjustment sun protection control (up/down) and slat control (open/close) -Bus-powered electronics -Integrated bus coupling units -Bus connection via bus terminal or contact system to data rail -Modular installation devices for mounting on TH35 EN 60715 mounting rail The data rail must be ordered separately. See chapter System Products and Accessories - data rails.

-For the separate control per actuator channel of a sun protection, damper, door or window drive with a motor for AC 230 V and electromechanical or electronic limit switches -Integrated electronics for detection of the actuation of an electromechanical limit switch and with auto-calibration of the travel time from one limit switch to the other -Electrically interlocked relays to reverse the direction of rotation -Relay contacts rated for nominal voltage AC 230 V, 8 A (resistive load) -Configuration by the user whether all actuator channels are to be identically or individually parameterized -Communication objects per actuator channel for moving the sun protection to the limit positions or to stop travel and for step-by-step adjustment of the blind slats -Communication objects for moving the sun protection and adjusting the blind slats directly to a new position (as precisely as drive mechanics permit) by positioning commands as percentage values -Automatic opening of blind slats up to a set position after the blinds have been lowered without any stop from the upper to the lower limit position -Integrated 1-bit scene control for save and recall of 2 favored positions of blind and slats -Integrated 8-bit scene control and assignment of up to 8 scenes per channel -Optional object “Sunshine” for activation / deactivation of sunlight tracking of the slats for shading with greatest possible daylight component -Differentiation between automatic and manual mode and with automatic switchover from automatic to manual mode of the respective actuator channel on activation of a bus pushbutton for manual control of the sun blind -Priority of manual mode over automatic positioning commands -Alarm object per device or per channel for moving the sun protection to the configured safety position in the event of a wind alarm e.g. and with blocking of travel to another position as long as alarm pending -Travel blocking object per device or per channel for blocking the sun protection in its current position (needed during cleaning of an outdoor Venetian blind e.g.) -Status objects per actuator channel for query or automatic transmission of sun blind and slat position as percentage value -Electronics powered via an integrated power supply unit for AC 230 V -Green LED for displaying the 230 V operating voltage -Pushbutton for switchover between bus mode and direct mode -Yellow LED for display of activated direct mode -Two pushbuttons each per actuator channel for drive control in direct mode -Integrated in the actuator housing and operational if the actuator is supplied with AC 230 V (even if bus voltage missing or communication not operational) -Integrated bus coupling unit with only half a standard bus load -Bus connection via bus terminal or contact system to data rail -Modular installation devices for mounting on TH35 EN 60715 mounting rail The optional data rail must be ordered separately. See chapter System Products and Accessories - data rails.

-4 channels -For the separate control per actuator channel of a sun protection‚ damper‚ door or window drive with a motor for AC 230 V and electromechanical limit switches -Rated contact voltage AC 230 V, 50 Hz -Status position of slats, 8-bit -Integrated 1-bit scene control, 2 Scenes to be integrated per channel -Separate raising/lowering protection -Integrated power supply unit for the electronics, connected to AC 230 V -Sun protection control (up/down) using position data (8-bit value) The optional data rail must be ordered separately. See chapter System Products and Accessories - data rails.

-4 channels -For the separate control per actuator channel of a sun protection‚ damper‚ door or window drive with a motor for AC 230 V and electromechanical limit switches -Rated contact voltage AC 230 V, 50 Hz -Automatic mode for sunlight tracking control -Manual mode -Indication of direct operation with status object -Status position of slats, 8-bit -Suitable for integration in a sunlight tracking control system -Sun protection control (up/down) using position data (8-bit value) -Integrated power supply unit for the electronics, connected to AC 230 V -Slat control (open/close) using position data (8-bit value) or travel to end position, stopping, stepwise adjustment The optional data rail must be ordered separately. See chapter System Products and Accessories - data rails.