8 Inputs for AC/DC 12...230 V

16 Inputs for AC 12...230 V, DC 12...115 V

8 Inputs for AC/DC 12...230 V, 8 Inputs for floating contacts

2 inputs / outputs

4 inputs / outputs

-One output for switching and dimming resistive, inductive or capacitive loads -With semiconductor output for switching and dimming of lamps -Rated operational voltage AC 230 V, 50/60 Hz -Connected load 50...210 VA -Settable switching and dimming behaviour -Selectable mode of operation (normal mode, timer mode) -Soft on, Soft off -Dimming or jumping to a new dimming value -Time-delayed switch-off when dimming below a settable dimming value -Status objects for switching and dimming value -Short-circuit message -Message of a load failure -Integrated 8-bit scene control -Object for blocking the output -Configurable brightness value at start and end of a blocking phase -Adjustable behaviour of the output after bus voltage recovery -2 binary inputs for potential-free contacts -Selectable function of the binary inputs: acting as secondary inputs directly on the switching outputs or acting as independant binary inputs with bus communication -Free allocation of the functions switching, dimming, solar protection control, send value and scene control to the inputs -Two independent switching objects per input -Blocking object for each input -Separately selectable behaviour per input at bus voltage recovery -Telegram rate limitation for both inputs -About 20 cm long wires for connecting phase conductor, output, inputs and bus -Bus-powered electronics -Integrated bus coupling unit -Enclosed bus terminal for bus connection -For installation in a flush-mounting wall or ceiling box with 60 mm diameter

Dimmer output 20...500 VA

Dimmer output 20...500 VA

Dimmer output 20...1000 VA, parallel operation of the outputs for doubling the dimming power to 40...2000 VA

Dimmer output 20...300 VA

Dimmer output 20...300 VA

-8 DALI outputs -Control capacity for up to 8 DALI-ECGs per DALI output -Power supplied to the electronics and the DALI outputs through an integrated power supply unit for 230 V AC -Green LED for status display -Pushbutton for selecting and switching over 4 DALI outputs respectively between bus and direct mode -Yellow LED for indicating which 4 DALI outputs the direct mode is activated for -1 red LED per DALI output for indicating the circuit state or fault (e.g. lighting medium failure) of the connected group -Four pushbutton pairs for switching and dimming of 4 DALI outputs in direct mode, functional when 230 V AC is applied (also when no bus voltage is connected and also when bus communication has not yet been started or is interrupted) -Selection of identical or individual configuration of all DALI outputs -Selectable operating mode per DALI output (normal mode, 1-level or 2-level time-switch mode) -Per DALI output with command objects for switching on/off, dimming brighter/darker and setting dimming value -Per DALI output optionally with up to 4 add-on status objects (circuit state and lighting medium failure, dimming value status and DALI status) -Sending of status objects on request and/or automatically after change -Per DALI output with add-on object for time-limited switching on of lighting in night mode (cleaning light) -Warning approx. 1 minute before imminent switching off, by dimming to 50 % of former dimming value in night or timer mode -Adjustable switching on and/or off of a channel through dimming brighter/darker, dimming value when switching on, actuating or dimming a new dimming value, dimming time from 0% to 100% -Adjustable behavior on bus voltage or mains voltage failure and bus voltage or mains voltage recovery -Add-on object and integrated 8bit scene control for saving and restoring up to 16 scenes per DALI output -Integrated bus coupling unit as only half standard bus load -Bus connection through bus terminal as well as contact system to data rail -Device for mounting on rail TH35 DIN EN 60715 The data rail must be ordered separately. See chapter system products and accessories - data rails.

-For switching and dimming of eight mutually independent groups (channels) of fluorescent lamps with dimmable electronic control gear (ECG) -8 control voltage outputs 1...10 V DC -Control power min. 60 OSRAM ECG dynamic each -8 switching outputs (relay contacts) for 230 V AC, 50/60 Hz, 16 A at p.f. = 1 -Each of them for connection of min. 30 OSRAM ECG dynamic for 58 W fluorescent lamps -Slide switch per relay output for manual operation and switch position indication -Selection between identical or individual configuration of all channels -Command objects for each actuator channel for switching on/off, dimming brighter/darker and set/value -One 1-bit and one 8-bit-status object (switching state and dimming value) per output -Per channel configurable time-limited activation of the lighting during night mode (base lighting) -Warning 30 seconds prior to imminent switch off by dimming to 50 % of the previous dimming value for each channel with time-limited operation -Switching on or off of a channel by dimming brighter/darker -Configurable dimming value upon switching on -Jumping or dimming to a new dimming value -Configurable dimming time from 0...100% -Integrated 8 bit scene control and assignment of each output to up to 8 scenes -Transmission of status objects on request, cyclically and/or automatically after changes -Configurable behaviour on bus voltage failure and recovery -Bus-powered electronics -Integrated bus coupling unit, bus connection via bus terminal or contact system to data rail -Modular installation devices for mounting on TH35 EN 60715 mounting rail The data rail must be ordered separately. See chapter system products and system accessories - data rails.

-For covering free data rail segments (in accordance with the SELV regulations for safety extra-low voltage) -For snapping onto standard mounting rails, separable, RAL 7035 -Length 13.5 MW (1 MW = 18 mm)

For the protection of already installed flush-mounting bus coupling units, DELTA bus coupling units or flush-mounting actuators with user interface (UI) through to the mounting of bus terminals

-For four Pt1000 sensors -For the measurement and transmission of 4 temperatures in the range -40...+150 °C -For connection of four Pt1000 temperature sensors2), each via a 2-wire cable up to 50 m in length -Configurable smoothing of a measured value through mean value generation -Monitoring of a lower and upper limit value for each measured value, with configurable hysteresis for limit value signals -Electronics powered via an integrated power supply unit for 230 V AC -Green LED for displaying ready-to-run status -Integrated bus coupling units -Bus connection via bus terminal or contact system to data rail -Modular installation devices for mounting on TH35 EN 60715 mounting rail The accompanying physical sensors must be ordered separately. See chapter Physical sensors - sensors without KNX connection.The data rail must be ordered separately. See chapter System Products and Accessories - data rails.

2 facing pushbutton rockers Аксессуары для клавиш UP223 и UP287 с ИК-приёмником и декодером

4 facing pushbutton rockers Аксессуары для клавиш UP223 и UP287 с ИК-приёмником и декодером